“Recently did work on our house (new siding and added a portico). They did a great job, were courteous, professional and very fair with pricing. Would highly recommend.”
Flooring
Flooring in Southeast Massachusetts.
Flooring shows every flaw in the subfloor, every gap in the install, every misread of the moisture content. We level, acclimate, and install with the patience the material requires. Refinishing too: three-pass sanding, dust containment, oil or water finish. Our published range is $2,500-$22,000 per project, and the walk-through and written estimate are free.
A flooring job with CW Services LLP runs $2,500 to $22,000 and moves through five stages: (1) a walk-through and written estimate, usually sent the same week; (2) measuring and material selection, with labor and materials priced separately; (3) subfloor prep, which is where most bad floor jobs actually go wrong; (4) installation by one crew, start to finish; and (5) a final walk-through before the last payment, backed by a written one-year workmanship warranty. The real choice most owners weigh is this: a handyman is cheaper for one small job but carries no warranty and pulls no permits; a large design-build firm brings a showroom and a designer at a markup you pay for; a family-run licensed contractor like this one sits between them, with one crew and Glenn on site most days. This is not the right fit if you want the lowest bid on the street, if your address falls outside the 14 towns we serve, or if the job is an emergency needed today rather than a planned project. The takeaway: get the free written estimate and compare it line by line against anything else you have been quoted.
- Cost range
- $2,500-$22,000
- Typical timeline
- 4-11 days
- What we handle
- 5+ project types
Quick answer
Flooring in Southeast Massachusetts from CW Services LLP runs $2,500-$22,000 per project (our published price), with a typical timeline of 4-11 days. Glenn and his crew handle every trade in-house with licensed electrical and plumbing partners. Every project carries a written 1-year workmanship warranty, MA HIC license, and $2M general liability.
Free walk-through within 3-5 business days, written estimate the same week, and same crew start to handoff. Call (774) 623-9476 or request a free estimate.
What we do
Project types.
CW Services LLP handles 5 types of flooring work in Southeast Massachusetts, from hardwood install to subfloor leveling. Pricing typically runs $2,500-$22,000 per project, depending on scope and finish level. Glenn scopes the right project type during a free walk-through and writes the estimate the same week.
Hardwood install
Solid or engineered, nail-down or glue-down.
Hardwood refinishing
Sand, stain, seal, water or oil-based finish.
Luxury vinyl plank (LVP)
Click-lock or glue-down. On slab or subfloor.
Tile flooring
Kitchens, bathrooms, mudrooms, entries.
Subfloor leveling
Self-leveler or shim-and-plywood, whichever the situation calls for.
Process
From walk-through to handoff.
A flooring project at CW Services LLP runs in 5 stages: walk-through & estimate, acclimate the material, subfloor prep, install, transitions, trim, walk-through. Glenn walks the home, writes the estimate the same week, pulls every permit, and the same crew handles every trade through finish. Typical timeline is 4-11 days, with a written 1-year workmanship warranty included.
- 01
Walk-through & estimate
Glenn checks subfloor flatness, moisture, transitions. We write the estimate the same week.
- 02
Acclimate the material
Hardwood and LVP sit in the home for 5-7 days before install. Skipping this is why floors gap.
- 03
Subfloor prep
Level dips, screw down squeaks, vapor barrier where needed. The base matters more than the floor.
- 04
Install, transitions, trim
Stagger cuts properly, transition pieces seated tight, shoe molding caulked at the wall.
- 05
Walk-through
Final clean, walk-through. Written workmanship warranty.
FAQs
Common questions.
If your question isn’t answered here, call or text Glenn at (774) 623-9476.
How long does install take?
A 600 sqft hardwood install runs 4-6 days. Refinishing runs 3-5 days plus dry time.
Can you install over my existing floor?
Sometimes, depends on the substrate and ceiling height. We will tell you when it makes sense and when it does not.
Will refinishing be dusty?
Less than you expect. We use dust-containment sanders and seal off rooms. Plan to be out of the house for finish coats.
What does it cost?
LVP starts around $5-$8/sqft installed. Hardwood install is $9-$14/sqft. Refinishing existing hardwood is $4-$6/sqft.
Planning guide
Before you call about flooring.
Hardwood, LVP, tile, and refinishing, installed flat, sanded right. Settling the four questions below before the walk-through makes the flooring estimate faster and closer to what you actually want, because Glenn can price the job you have decided on instead of a guess at it.
What should you decide before choosing a material?
Decide which rooms are getting new flooring and whether moisture, like a kitchen, bathroom, or mudroom, rules out certain materials before you fall in love with a look. Think about how the new flooring will meet existing floors in hallways and doorways, since transitions are easy to overlook until installation day. If you are refinishing existing hardwood, decide whether you want an oil or water-based finish, since they differ in look, smell during the process, and how long you need to stay off the floor. Walk the rooms and check for squeaks, dips, or soft spots now, since those affect subfloor prep more than the finish material itself.
What should you ask about subfloor and acclimation?
Ask whether your subfloor is flat enough for the material you want, and what leveling or repair work is included if it is not, since flooring shows every flaw underneath it. Ask how long hardwood or LVP needs to sit in the home before installation, since skipping acclimation is a common reason floors gap or buckle later. Ask whether the new material can go over your existing floor or needs a full tear-out, since substrate and ceiling height both play a role. If tile is planned for a wet area, ask how the subfloor is prepared to handle moisture over time.
How should you prepare the house before installation?
Clear furniture, rugs, and breakables out of every room getting new flooring or refinishing, and plan where they will sit for the length of the project. If hardwood is being refinished, plan to be out of the house during finish coats, since dust containment reduces mess but does not eliminate the need for ventilation and dry time. Confirm pets have a safe space away from open work areas and drying finishes. Ask about transition points between rooms and levels so you know which doors may need trimming and which thresholds are being replaced.
What should you check once the floor is installed?
Walk the finished floor in socks and check for squeaks, soft spots, or movement, since a properly leveled and acclimated install should feel solid underfoot. Look closely at transition pieces between rooms and at how trim and shoe molding were caulked along the walls. Check stagger patterns on plank flooring for a natural, non-repetitive look rather than an obvious grid. Ask what the written workmanship warranty covers and how long refinished hardwood needs before furniture and rugs go back down, and confirm the final clean-up was thorough before moving everything back in.
What actually drives the scope of a flooring project?
Scope in flooring depends heavily on what is under the surface you cannot see until work begins. A flat, dry subfloor in good condition supports a straightforward install, while dips, squeaks, or old adhesive residue add leveling and prep work before the new material ever goes down. Material choice changes the process too, engineered hardwood and LVP install differently than solid hardwood or tile, and refinishing existing wood is a different scope entirely from installing something new. Room shape and the number of transitions to other flooring types also add labor that a simple open room does not need. Flagging known trouble spots, soft boards, old squeaks, uneven areas, helps the crew plan for what subfloor prep will actually involve.
How does new flooring interact with the rest of the house?
Flooring connects rooms to each other more directly than most other trades, since transitions at doorways and open layouts need to line up cleanly between spaces that may not be part of the current project. Baseboards and shoe molding throughout the house often need to be removed and reset, which can expose old paint lines or gaps that were previously hidden. If flooring changes thickness, from old carpet to hardwood for example, doors may need trimming to clear the new surface. Furniture from adjoining rooms sometimes needs to move temporarily even if those rooms are not getting new flooring, simply to clear a path for material and equipment.
How can you tell a rushed flooring job from a quality one?
A rushed flooring job shows in gaps between boards, squeaks that appear within the first season, and transition pieces that were forced rather than fitted. Quality work starts before installation, with material properly acclimated to the home and a subfloor that was actually leveled rather than installed over as is. Check that plank patterns look intentional rather than repetitive, that grout lines on tile are consistent, and that trim and shoe molding sit tight against the floor without visible gaps. A floor that flexes underfoot in spots, or that develops a hollow sound when tapped, points to subfloor prep that was skipped to save time.
What should you ask any contractor before hiring for flooring?
Ask how long they let material acclimate in the home before installing it, since a short answer here often points to a shorter finished life for the floor. Ask how subfloor issues get identified and priced if they are found once old flooring comes up, so you are not surprised by a change order later. Ask how transitions between rooms and flooring types are planned, especially where your project meets flooring that is not being replaced. Ask whether refinishing uses dust containment and how long you need to stay off the finish before furniture goes back. Ask for the written workmanship warranty so you know what is covered if something moves after the first season.
Choosing a contractor
DIY vs handyman vs CW Services.
For a flooring project, here’s the honest tradeoff. Some scopes really are best handled by a handyman. Some truly should be DIY.
Pulls permits & meets inspectors
DIYNoHandymanPartialCWYesLicensed for structural changes
DIYNoHandymanNoCWYesCoordinates licensed electrical & plumbing
DIYNoHandymanPartialCWYesWritten estimate, line-itemed
·DIYn/aHandymanPartialCWYesSame crew start to handoff
·DIYn/aHandymanNoCWYesWritten 1-yr workmanship warranty
DIYNoHandymanNoCWYesInsurance + workers comp on every employee
DIYNoHandymanPartialCWYesEPA Lead-Safe certified (pre-1978 homes)
DIYNoHandymanNoCWYesDaily clean-up + dust control
DIYPartialHandymanPartialCWYesHonest about scope creep before extra work
·DIYn/aHandymanPartialCWYes
Honest answer: a handyman is right for a leaky faucet or trim repair. A licensed GC is right for moving plumbing, walls, or systems. We’ll tell you straight, and refer you out when we’re not the right fit. Not sure which your project needs? Ask for a free walk-through.
Reviews
Same crew. Same standard. Years of receipts.
“I hired CW for multiple projects and Glen is so easy to work with. There pricing has been totally reasonable. They are always on time and do excellent work. I will hire him for any future projects!”
“They did work on my home they were very reliable and kind. The work was great! I had a wonderful experience and Highly recommend them!”
“Glen painted, repaired and built a privacy fence on my deck. It all came out great! Thanks Glen!”
Also serving
Flooring, town by town.
Pick your town for local pricing, permit notes, and recent flooring work nearby.
Related
Other services we handle.
Ready to talk through your project?
Free estimate. Written same week. Glenn walks the project, Megan handles scheduling. No pressure, no salesperson.